suki@tdfasteners.com
Call Us M.T:0086-013757473258
News

Stainless steel is principally known and considered for use because of its high level of corrosion resistance in both wet and dry conditions, particularly in comparison with standard carbon steels.

Read Details

A2 - The most commonly produced grade of stainless steel. Also known as grade or type 304.A4 - The second most commonly produced grade of stainless steel. Also known as grade or type 316.A/F - A shortened form of 'width across flats'.Acorn Nut - Another name for a dome nut.Allen Key - A tool with a hexagonal cross section used for tightening up screws with a socket head.Allthread - A metal bar that has a thread all along its length.

Read Details

The following table describes the strength specifications for the different property classes of metric steel bolts, screws and studs:

Read Details

The following table lists the most popularly used threaded fasteners used today, and the DIN standard or otherwise to which they have been designed:

Read Details

Threaded Fasteners - An Overview of Thread Standards Standardisation of screw thread forms is an ongoing process begun in the 19th century.

Read Details

Standard: ASTM A325/Din933 hex bolts Dia.: 1/2""-1 1/2""; Length:1 1/4""-8""; Surface treatment: Plain ,Black oxygenation, HDG Scope The ASTM A325 specification covers high strength heavy hex structural bolts from ½” diameter through 1-1/2” diameter. These bolts are intended for use in structural connections and therefore have shorter thread lengths than standard hex bolts. Refer to the Structural Bolts page of our site for thread lengths and other related dimensions.

Read Details

The American Society for Testing and Materials, is an international standards organization that develops and publishes voluntary consensus technical standards for a wide range of materials, products, systems, and services.

Read Details

The ASTM A153 specification covers zinc coating (hot-dip) on iron and steel hardware. A newer and more appropriate specification developed in 2005 covering the requirement for hot-dip galvanizing of bolts, screws, nuts, washers and other threaded fasteners

Read Details

Originally approved in 1936, this specification is heavily utilized in petroleum and chemical construction applications. The ASTM standard covers alloy steel and stainless steel bolting materials for high temperature service.

Read Details

The ASTM A194 specification covers carbon, alloy and stainless steel nuts intended for use in high-pressure and/or high-temperature service. Unless otherwise specified, the American National Standard Heavy Hex Series

Read Details

Originally approved in 1948, the ASTM A320 specification covers alloy steel and stainless steel bolting materials for low temperature service. This standard covers rolled, forged, or strain hardened bars, bolts, screws, studs, and stud bolts used for pressure vessels, valves, flanges, and fittings. Like the ASTM A193 specification, unless otherwise specified, the 8UN thread series is specified on fastener larger than 1” in diameter.

Read Details

The ASTM A307 specification covers carbon steel bolts and studs ranging from 1/4” through 4” diameter. This is your everyday, run of the mill bolt specification often manufactured using A36 round bar. There are three grades A, B, and C* which denote tensile strength, configuration, and application. Refer to the Mechanical Properties Chart for the subtle strength differences within each grade.

Read Details

The ASTM A325 specification covers high strength heavy hex structural bolts from ½” diameter through 1-1/2” diameter. These bolts are intended for use in structural connections and therefore have shorter thread lengths than standard hex bolts. Refer to the Structural Bolts page of our site for thread lengths and other related dimensions.

Read Details

The ASTM A354 specification covers the chemical and mechanical requirements of quenched and tempered alloy steel bolts, studs, and other externally threaded fasteners 4"" and under in diameter.

Read Details

ASTM A449 covers headed bolts, rods, and anchor bolts in diameters ranging from 1/4"" through 3"" inclusive. It is a medium strength bolt manufactured from a medium carbon or alloy steel that develops its mechanical values through a heat treating process. It is intended for general engineering applications.

Read Details